# How do I set XYZ for material that is 1/8" thick

**URL:** <https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978>\
**Category:** ❓ Question\
**Created:** [January 19, 2022, 9:51pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978 "2022-01-19T21:51:22Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![hectorton](https://forum.sienci.com/letter_avatar_proxy/v4/letter/h/b9bd4f/32.png) [@hectorton](https://forum.sienci.com/u/hectorton)\
**Post date:** [January 19, 2022, 9:51pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/1 "2022-01-19T21:51:22Z")

</div>

The Sienci touch plate is milled for material thickness of a 1/4" minimum. How do I set the xyz for material that is 1/8" thick (6061 aluminum) given that the touch plate is not usable. Thanks in advance.

---

<div class="post-metadata">

**Author:** ![JayKent242](https://forum.sienci.com/letter_avatar_proxy/v4/letter/j/49beb7/32.png) [@JayKent242](https://forum.sienci.com/u/JayKent242)\
**Post date:** [January 19, 2022, 9:59pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/2 "2022-01-19T21:59:51Z")

</div>

You could use the touch plate to do the X and Y because it’ll still sit on the edge of 1/8 material. Zero out the X and Y.  
Then manually move the z to the top of the work surface. I put a sheet of paper underneath the bit and move the bit down till I can’t pull the paper out. Zero out the Z.

Hope this helps

---

<div class="post-metadata">

**Author:** ![hectorton](https://forum.sienci.com/letter_avatar_proxy/v4/letter/h/b9bd4f/32.png) [@hectorton](https://forum.sienci.com/u/hectorton)\
**Post date:** [January 19, 2022, 10:46pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/3 "2022-01-19T22:46:05Z")

</div>

Thank you very much. Worked like a charm.

---

<div class="post-metadata">

**Author:** ![ozguzzi](https://forum.sienci.com/letter_avatar_proxy/v4/letter/o/958977/32.png) [@ozguzzi](https://forum.sienci.com/u/ozguzzi)\
**Post date:** [January 20, 2022, 12:09am UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/4 "2022-01-20T00:09:42Z")

</div>

Like Jay said for the X Y, then just flip the touch plate over and do the Z.

---

<div class="post-metadata">

**Author:** ![gwilki](https://forum.sienci.com/user_avatar/forum.sienci.com/gwilki/32/366_2.png) [@gwilki](https://forum.sienci.com/u/gwilki)\
**Post date:** [January 20, 2022, 2:33pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/5 "2022-01-20T14:33:08Z")

</div>

As the original issue has been addressed, I’m closing this topic. If anyone else has a similar concern, feel free to start a new topic, which will ensure that it is addressed promptly.

---

<div class="post-metadata">

**Author:** ![gwilki](https://forum.sienci.com/user_avatar/forum.sienci.com/gwilki/32/366_2.png) [@gwilki](https://forum.sienci.com/u/gwilki)\
**Post date:** [January 20, 2022, 2:33pm UTC](https://forum.sienci.com/t/how-do-i-set-xyz-for-material-that-is-1-8-thick/4978/6 "2022-01-20T14:33:12Z")

</div>

Closed on January 20, 2022, 2:33pm UTC


