# Maintenance - Lubrication

**URL:** <https://forum.sienci.com/t/maintenance-lubrication/17026>\
**Category:** 🧠 New Wisdom\
**Created:** [April 25, 2025, 8:49pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026 "2025-04-25T20:49:58Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [April 25, 2025, 8:49pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/1 "2025-04-25T20:49:58Z")

</div>

Hey everyone in Sienci Labs land!

I just completed my second maintenance run on my AltMill and decided to do [a video](https://www.instagram.com/p/DI4ZodNyF3G/) about it.

In the video’s text description you’ll note that I found three issues with my machine, which I’ve overcome as indicated below:

1. The right-side Y-rail’s ball screw assembly arrived flipped over, making the grease nipple inaccessible. It was a simple matter of undoing the 4 screws holding it to the X-axis gantry plate, then turning it over. Interestingly enough, once I’d finished the job and had the machine move under power to its home position (back left corner for me) , this half-turn didn’t affect the precision of the machine, as a check confirmed.
2. The X-axis dome-headed screws (4 of them) were all missing from my machine. I’ve contacted Sienci Labs to send me 4 of them.
3. Oiling the Z-axis bottom set of bearings appears to be an impossible task, as the dome-headed screws are located on their underside. (oil doesn’t run uphill very well 🫠). So to lube them, I oiled the ways (the two rails), and ran the assembly slowly up and down to get the oil up into the bearings.

Lubricating your AltMill is a relatively straight-forward undertaking and after you’ve done it a few times it should take only 15 minutes or so. Easy Peesy!

Marty from Kingston, ON 🇨🇦

---

<div class="post-metadata">

**Author:** ![WaldosWoodworking](https://forum.sienci.com/letter_avatar_proxy/v4/letter/w/0ea827/32.png) [@WaldosWoodworking](https://forum.sienci.com/u/WaldosWoodworking)\
**Post date:** [April 29, 2025, 1:55pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/2 "2025-04-29T13:55:09Z")

</div>

I replaced all 12 linear guide block screws with brass M5 grease fittings and use a needle nozzle on my grease gun. The small tapered tip of the nozzle presses the ball of the zero in so grease can easily be applied. This is especially useful for the bottom blocks of the Z axis linear guide blocks.  
I use Mobil EP 2 grease on all 12 guide blocks and all 4 ball screw blocks.

---

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [April 30, 2025, 8:01pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/3 "2025-04-30T20:01:37Z")

</div>

Tom, would you happen to have photos showing the grease fittings and how much clearance there is between the two lower Z-axis linear guide blocks and the spoil board?  
Much appreciated!

Marty from Kingston, ON 🇨🇦

---

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [April 30, 2025, 8:03pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/4 "2025-04-30T20:03:38Z")

</div>

Hey, Tom,

Thanks again for sharing your method of lubricating the linear blocks. It appears that Sienci Labs modified their lubrication instructions to now include greasing as well as oiling them. I have a feeling that the reason for this was the relatively difficult time users were having to acquire that particular oil… but I’m not sure if there’s much difference between the two lubricants in this particular application.

While researching the topic I came across [this information](https://www.thomsonlinear.com/en/support/tips/what-should-be-used-to-lubricate-linear-bearings) provided by Thompson, a bearing and stepper motors specialty company. As you can see, they recommend machine oil or low viscosity grease for light loads and high speeds, NLGI 1 or 2 grease for medium speeds and loads and a grease with an EP2 additive for high loads. I’m not sure how much loading the linear bearings take, but I have a hunch it’s fairly light.

Thoughts, anyone?

Marty from Kingston, ON 🇨🇦

---

<div class="post-metadata">

**Author:** ![tiermanc](https://forum.sienci.com/letter_avatar_proxy/v4/letter/t/59ef9b/32.png) [@tiermanc](https://forum.sienci.com/u/tiermanc)\
**Post date:** [May 14, 2025, 1:28pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/5 "2025-05-14T13:28:48Z")

</div>

Vactra Oil on Amazon [Amazon.com: VACTRA OIL NO 2. 1 Quart(32OZ) NO AIR SHIPMENTS : Industrial & Scientific](https://a.co/d/0surutC)

---

<div class="post-metadata">

**Author:** ![tiermanc](https://forum.sienci.com/letter_avatar_proxy/v4/letter/t/59ef9b/32.png) [@tiermanc](https://forum.sienci.com/u/tiermanc)\
**Post date:** [May 14, 2025, 1:34pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/6 "2025-05-14T13:34:23Z")

</div>

![image](https://forum.sienci.com/uploads/default/original/2X/f/f84a010f149b5fc2f1165c2427c4f8f3f864436b.png)

This is the grease I used on my Next Wave HD520. I definitely use the grease tip to get into the tight spots like behind the spindle carriage. I purchased this off the Next Wave website.

---

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [May 15, 2025, 9:51am UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/7 "2025-05-15T09:51:40Z")

</div>

Thanks for the lead, as that’ll help any US based members. Canadians don’t have that option for either of the two lube products you’ve mentioned as [Amazon.com](http://Amazon.com) won’t ship them to Canada.

---

<div class="post-metadata">

**Author:** ![Jens](https://forum.sienci.com/letter_avatar_proxy/v4/letter/j/d2c977/32.png) [@Jens](https://forum.sienci.com/u/Jens)\
**Post date:** [May 15, 2025, 12:50pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/9 "2025-05-15T12:50:24Z")

</div>

Actually I got both of those lubricants from Amazon.ca

> **[Mobil 100772 Vactra No.2 Way Oil 1 gal : Amazon.ca: Tools &amp; Home Improvement](https://www.amazon.ca/Mobil-100772-Vactra-No-2-Way/dp/B07B7XZKVF)**
>
> Mobil Vectra Oil No. 2 is recommended for horizontal slide ways on small to medium size machine tools. It is also suitable for flood application in large machines.

It unfortunately took a BIG jump in price in February

> **[Mobil 122136 EP 2, EP Grease, NLGI 2, 13.7 oz. : Amazon.ca: Automotive](https://www.amazon.ca/Mobil-122136-Automotive-Accessories/dp/B01N191WZE)**
>
> Industrial Grade Grease, Lithium Hydroxystearate Base, Size 14 oz. , Container Type Cartridge, NLGI Grade 2, Color Brown, Temp. Range -20 Degrees to 130 Degrees C, Flash Point Not Specified, Dropping Point 190 Degrees C, Four-Ball Wear 0. 4mm,...

The grease is currently not available

---

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [May 16, 2025, 12:46pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/10 "2025-05-16T12:46:30Z")

</div>

Yes, those are similar links which I’d shared with others previously. The main difference between the [Amazon.com](http://Amazon.com) and Amazon.ca product is in the oil. Here in Canada we can only get it in the larger 1 gallon format, which is enough to do 10 CNCers their entire lifetimes!

---

<div class="post-metadata">

**Author:** ![emelchor](https://forum.sienci.com/letter_avatar_proxy/v4/letter/e/c37758/32.png) [@emelchor](https://forum.sienci.com/u/emelchor)\
**Post date:** [August 28, 2025, 10:15pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/11 "2025-08-28T22:15:27Z")

</div>

Marty,

I am in the process of doing the maintenance on my Altmill and wanted to get a better understanding of the issue with the ball screw on the left side Y axis.

Can you please elaborate on what you mean by “turning it over” for the ball screw? I don’t quite follow your explanation. I have remove the 4 screws on the X-axis gantry but don’t see how the ball screw can be turned over or flipped.

This is the orientation of my ball screw at this time. Is this how the ball screw was oriented your your machine?

 ![Altmill Ball Screw](https://forum.sienci.com/uploads/default/original/2X/2/2fa2a39254761b23d436891aeec9034ef036a170.jpeg)

If you could, please provide me with how to move the nipple for easier access.

Thanks,

Eddy

---

<div class="post-metadata">

**Author:** ![ApexWoodworks](https://forum.sienci.com/letter_avatar_proxy/v4/letter/a/e19adc/32.png) [@ApexWoodworks](https://forum.sienci.com/u/ApexWoodworks)\
**Post date:** [August 30, 2025, 9:07pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/12 "2025-08-30T21:07:17Z")

</div>

Eddy,

If you remove the 4 machine screws holding the ball screw to the gantry plate on that side, then jog the machine 80mms backwards (document the exact distance you moved it, so that you can move it back when you’re done). That will then provide you enough free space between the assembly and the rail to allow you to carefully rotate the ball screw assembly 180 degrees (the rotation direction won’t matter). Doing so will temporarily bend the drive screw very slightly, but it’s resilient enough to return back to its original position right away. There should be enough slack space between the assembly and the rail to allow you to rotate it without undue force. Then before doing anything else, jog the machine forward the same distance you’d moved it prior to rotating the ball assembly. If you did that correctly, because the screw holes in that assembly are drilled completely through, the holes in the gantry bracket and the ball assembly should be lined up perfectly. Because the holes are threaded the full way, you should be able to then screw the machine screws back into place. DON’T overtighten them, as you’ll risk stripping them. I used a bit of LokTite (the low strength version) on the screws just for added security against them loosening off.

Hope this answers your question.

Cheers,

Marty from Kingston, ON 🇨🇦

---

<div class="post-metadata">

**Author:** ![acruther](https://forum.sienci.com/user_avatar/forum.sienci.com/acruther/32/11262_2.png) [@acruther](https://forum.sienci.com/u/acruther)\
**Post date:** [April 5, 2026, 7:31am UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/13 "2026-04-05T07:31:23Z")

</div>

Would this be a “good enough” grease gun for the AltMill? Price is right…

[https://www.harborfreight.com/pistol-grip-grease-gun-70702.html?hftm\_sc=422&hftm\_source=google](https://www.harborfreight.com/pistol-grip-grease-gun-70702.html?hftm_sc=422&hftm_source=google)

---

<div class="post-metadata">

**Author:** ![Chucky\_ott](https://forum.sienci.com/user_avatar/forum.sienci.com/chucky_ott/32/8692_2.png) [@Chucky\_ott](https://forum.sienci.com/u/Chucky_ott)\
**Post date:** [April 5, 2026, 9:38am UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/14 "2026-04-05T09:38:17Z")

</div>

@acruther Probably. I have a cheap one as well and it works fine. Difficult to get that grease cartridge in though. But it’s a big gun and unlikely I’ll ever fill it again considering the amount of grease you will use.

---

<div class="post-metadata">

**Author:** ![Dnick](https://forum.sienci.com/user_avatar/forum.sienci.com/dnick/32/9326_2.png) [@Dnick](https://forum.sienci.com/u/Dnick)\
**Post date:** [April 5, 2026, 4:15pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/15 "2026-04-05T16:15:34Z")

</div>

Here is what I am using for $16:

 ![Screenshot 2026-04-05 at 11.13.56 AM](https://forum.sienci.com/uploads/default/original/2X/5/57a9a612afe573e67a9b4f74e8377c86dcadd4e2.jpeg)

---

<div class="post-metadata">

**Author:** ![Opiate1](https://forum.sienci.com/letter_avatar_proxy/v4/letter/o/848f3c/32.png) [@Opiate1](https://forum.sienci.com/u/Opiate1)\
**Post date:** [April 7, 2026, 6:38pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/16 "2026-04-07T18:38:06Z")

</div>

Hello

would one be able to lubricate a longmill mk2 like this? currently i wipe down my lead screws then apply 3 in 1 oil. same with the z axix and on he slides. i will also use #0000 steel wool the X Y axis rails to knock the crud off.

thanks for any attention to this

---

<div class="post-metadata">

**Author:** ![Jens](https://forum.sienci.com/letter_avatar_proxy/v4/letter/j/d2c977/32.png) [@Jens](https://forum.sienci.com/u/Jens)\
**Post date:** [April 7, 2026, 7:25pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/17 "2026-04-07T19:25:11Z")

</div>

> [@Opiate1](#):
>
> i will also use #0000 steel wool the X Y axis rails to knock the crud off.

OMG … what could possibly go wrong …

---

<div class="post-metadata">

**Author:** ![Opiate1](https://forum.sienci.com/letter_avatar_proxy/v4/letter/o/848f3c/32.png) [@Opiate1](https://forum.sienci.com/u/Opiate1)\
**Post date:** [April 12, 2026, 5:04pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/18 "2026-04-12T17:04:58Z")

</div>

What do you mean? I haven’t had any problems

---

<div class="post-metadata">

**Author:** ![Jens](https://forum.sienci.com/letter_avatar_proxy/v4/letter/j/d2c977/32.png) [@Jens](https://forum.sienci.com/u/Jens)\
**Post date:** [April 12, 2026, 5:51pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/19 "2026-04-12T17:51:33Z")

</div>

You take a precision ground surface and you are introducing scratches. You might not see them but they are there. Thinking a bit more, you could be running wheels with the older mills (I have an Altmill and was horrified reading your post) and it might not be ‘much’ of a problem but no matter how you slice it, you do not want to touch a precision ground surface with anything abrasive unless you know what you are doing.

---

<div class="post-metadata">

**Author:** ![Spamming\_Eddie](https://forum.sienci.com/user_avatar/forum.sienci.com/spamming_eddie/32/7296_2.png) [@Spamming\_Eddie](https://forum.sienci.com/u/Spamming_Eddie)\
**Post date:** [April 12, 2026, 6:43pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/20 "2026-04-12T18:43:01Z")

</div>

When I clean my screw of crud, I temp mount a tooth pick on my x-gantry, have the tip fit into the grove and run the gantry down the full length of the axis. Cleans deep, fully, fast, easy, and gently.

It’s amazing what these grooves can hold. Even more amazing that the machine keeps running with all that sud tugged away.

Anyhooo, thought it would be nice to post an alternative manner to clean the screw without needing putting some back into it.

---

<div class="post-metadata">

**Author:** ![Jens](https://forum.sienci.com/letter_avatar_proxy/v4/letter/j/d2c977/32.png) [@Jens](https://forum.sienci.com/u/Jens)\
**Post date:** [April 12, 2026, 6:50pm UTC](https://forum.sienci.com/t/maintenance-lubrication/17026/21 "2026-04-12T18:50:31Z")

</div>

I was actually only thinking of the rails. I can’t envision cleaning a screw with steel wool (even 0000).  
Anyway, wheels can ride over small scratches but once you get into anything using ball bearings to roll on the surface of the mating part you want to avoid anything even remotely abrasive..

[Next page](https://forum.sienci.com/t/maintenance-lubrication/17026.md?page=2)
