# Trouble Getting Precision Cuts - Deflection of the Bit?

**URL:** <https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870>\
**Category:** 📄 General\
**Created:** [January 14, 2024, 2:35am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870 "2024-01-14T02:35:59Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![MajorSciGuy](https://forum.sienci.com/letter_avatar_proxy/v4/letter/m/f6c823/32.png) [@MajorSciGuy](https://forum.sienci.com/u/MajorSciGuy)\
**Post date:** [January 14, 2024, 2:35am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/1 "2024-01-14T02:35:59Z")

</div>

I finally decided to try my hand at inlays, but I can’t get the male and female to fit together properly. After a couple of tries with no success I tried to cut a simple circle inlay so I could see what was happening. The shape I get is not a perfect circle so the inlay did not work.

Had a similar problem trying to cut hidden box joints last week. The joints needed a lot of fine tuning after coming off the CNC.

I am left thinking that maybe the bit is deflecting? Everything else is tight as I just went over the machine to rule that out.

---

<div class="post-metadata">

**Author:** ![Lappa](https://forum.sienci.com/letter_avatar_proxy/v4/letter/l/5e9695/32.png) [@Lappa](https://forum.sienci.com/u/Lappa)\
**Post date:** [January 14, 2024, 3:43am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/2 "2024-01-14T03:43:42Z")

</div>

What bit are you using to machine the male and female inlay parts?

---

<div class="post-metadata">

**Author:** ![MikeH](https://forum.sienci.com/letter_avatar_proxy/v4/letter/m/258eb7/32.png) [@MikeH](https://forum.sienci.com/u/MikeH)\
**Post date:** [January 14, 2024, 3:49am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/3 "2024-01-14T03:49:38Z")

</div>

Is this a V carve inlay?

---

<div class="post-metadata">

**Author:** ![MajorSciGuy](https://forum.sienci.com/letter_avatar_proxy/v4/letter/m/f6c823/32.png) [@MajorSciGuy](https://forum.sienci.com/u/MajorSciGuy)\
**Post date:** [January 14, 2024, 3:57am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/4 "2024-01-14T03:57:18Z")

</div>

I am using a 0.125 flat endmill.

---

<div class="post-metadata">

**Author:** ![MajorSciGuy](https://forum.sienci.com/letter_avatar_proxy/v4/letter/m/f6c823/32.png) [@MajorSciGuy](https://forum.sienci.com/u/MajorSciGuy)\
**Post date:** [January 14, 2024, 3:58am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/5 "2024-01-14T03:58:10Z")

</div>

Started with a vcarve, but then went to a straight cut to simplify the troubleshooting.

---

<div class="post-metadata">

**Author:** ![MikeH](https://forum.sienci.com/letter_avatar_proxy/v4/letter/m/258eb7/32.png) [@MikeH](https://forum.sienci.com/u/MikeH)\
**Post date:** [January 14, 2024, 4:02am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/6 "2024-01-14T04:02:20Z")

</div>

Care to share the file and the settings?

---

<div class="post-metadata">

**Author:** ![\_Michael](https://forum.sienci.com/user_avatar/forum.sienci.com/_michael/32/2962_2.png) [@\_Michael](https://forum.sienci.com/u/_Michael)\
**Post date:** [January 14, 2024, 5:25am UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/7 "2024-01-14T05:25:30Z")

</div>

I’d like to share these resources on v-carve inlays in case you don’t have them.  
[VCarve\_Inlay\_Description\_and\_Procedure.pdf](https://forum.sienci.com/uploads/short-url/i2gFNI4x3v0UpaVZ8Po50YgKHRv.pdf) (1.1 MB)  
[VCarve\_Inlay\_Cheat\_Sheet.pdf](https://forum.sienci.com/uploads/short-url/wICj8ywYYXy0awbTryM11aO3Xfp.pdf) (188.8 KB)  
If you decide to try a v-carve inlay again those two documents have served me well.

I have never done a regular inlay so I’m not much help with those.

---

<div class="post-metadata">

**Author:** ![gwilki](https://forum.sienci.com/user_avatar/forum.sienci.com/gwilki/32/366_2.png) [@gwilki](https://forum.sienci.com/u/gwilki)\
**Post date:** [January 14, 2024, 1:32pm UTC](https://forum.sienci.com/t/trouble-getting-precision-cuts-deflection-of-the-bit/10870/8 "2024-01-14T13:32:41Z")

</div>

@MajorSciGuy You are on the right track going back to a simple circle to start your problem solving. Since you have said that everything is tight, I would run the calibrate tool to ensure that yourLM is moving as it should; that is, you tell it to move 10mm and it actually moves 10mm.
