gSender
📌 Release Thread 🐛 Bug ❓ Question 💡 Suggestion
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
gSender v1.0.1 and v1.0.2 Release
Hey folks, small build today to fix some recurring issues we’ve seen crop up over the past few weeks. 1.0.2 Fixed issue with XYZ Probing profile not moving in the X direction as far as it used to Fixed issue where cha… |
|
18 | 269 | December 4, 2021 |
|
BitSetter and other tool length sensors supported in gSender
Can anyone point me to information on using a tool height/offset probe for tool changing? I have a Shapeoko 3 with the BitSetter and I’m going to try setting up gSender instead of Carbide Motion…but glancing through the … |
|
22 | 345 | November 18, 2021 |
|
gSender pinned Wish List
Good day y’all! I know I had a thread previously for this but this world is all about learning and I quickly discovered that combining a post on issues as well as suggestions quickly became mostly issues which I feel ar… |
|
15 | 295 | October 16, 2021 |
|
Mini Numeric Keypad
Hi gang! In case anyone is interested in using the keybinding setup of gSender I ran across this neat numeric keypad on Amazon. I tried the Jelly Comb wireless USB but it didn’t have enough keys to cover all of the funct… |
|
9 | 318 | September 18, 2021 |
| G38.2 followed by runaway jog problem |
|
0 | 4 | December 5, 2021 |
| gSender 1.0.2 is available for download |
|
0 | 39 | December 4, 2021 |
| Black out bug - version 1.0.1 |
|
2 | 32 | December 3, 2021 |
| Touch Plate Settings |
|
1 | 50 | December 3, 2021 |
| Machine lock up |
|
1 | 53 | December 2, 2021 |
| Gamepad/Joystick Support |
|
28 | 384 | December 1, 2021 |
| GSender not maximized by default |
|
9 | 118 | November 30, 2021 |
| gSender 1.0.1 pause bug |
|
3 | 76 | November 28, 2021 |
| GSender Install Issue |
|
5 | 74 | November 27, 2021 |
| gSender 1.0.0 - Start at Line |
|
0 | 45 | November 26, 2021 |
| Feature Question |
|
2 | 45 | November 26, 2021 |
| gSender Z probe soft limit error |
|
6 | 164 | November 26, 2021 |
| Gsender 1.0.0 Z zero |
|
31 | 325 | November 26, 2021 |
| Selecting the connected machine |
|
3 | 67 | November 26, 2021 |
| What are the units for the numbers next to feed and spindle? |
|
28 | 216 | November 26, 2021 |
| Improvement suggestion |
|
0 | 40 | November 25, 2021 |
| Set my G54 offsets right after initialization |
|
1 | 68 | November 23, 2021 |
| Z changing during a carve |
|
7 | 87 | November 21, 2021 |
| Longtime carving |
|
2 | 59 | November 15, 2021 |
| Connecting xpro v5 to g sender |
|
5 | 57 | November 12, 2021 |
| Gsender 1.0.0 - Carbide Create/Post-Processor : Unsupported or Invalid GCode Command |
|
14 | 175 | November 10, 2021 |
| V1.0 problem Cripleware? |
|
2 | 86 | November 8, 2021 |
| Official 1.0.0 Release Thread: Stable 1.0 is finally here! |
|
4 | 116 | November 26, 2021 |
| gSender 1.0.0 pause bug |
|
2 | 112 | November 2, 2021 |
| Project too small After designing |
|
9 | 90 | November 2, 2021 |
| M0 pop-up stays |
|
16 | 248 | November 2, 2021 |