|
Front left corner button, no Z raise before XY movement
|
|
2
|
51
|
May 25, 2026
|
|
Cannot adjust feedrate during surfacing
|
|
3
|
83
|
May 24, 2026
|
|
Problems running macros from the SD card
|
|
7
|
132
|
May 21, 2026
|
|
When leaving rotary mode gsender not going to back the default
|
|
2
|
81
|
May 19, 2026
|
|
Heightmap gSender
|
|
65
|
2567
|
May 19, 2026
|
|
Linux questions
|
|
6
|
89
|
May 18, 2026
|
|
Gsender w/Genmitsu Wireless Controller
|
|
4
|
95
|
May 18, 2026
|
|
XY zero set at edge of bit not center
|
|
0
|
60
|
May 15, 2026
|
|
Spindle Speed Display
|
|
4
|
113
|
May 14, 2026
|
|
Fixed Tool Sensor "Probe Changed Tool" button permanently greyed out [Edge-4, grbl, macOS]
|
|
7
|
71
|
May 14, 2026
|
|
Visualizer no longer working in gSender 1.6?
|
|
0
|
40
|
May 13, 2026
|
|
Automations line pause
|
|
24
|
188
|
May 13, 2026
|
|
AutoZero incorrect Z height
|
|
6
|
88
|
May 13, 2026
|
|
Please Restore "Prompt for first tool" option in Edge-4 Tool Changing settings
|
|
1
|
38
|
May 13, 2026
|
|
Z Drive goes to the top limit upon starting a cut
|
|
5
|
60
|
May 13, 2026
|
|
Wear diameter compensation
|
|
6
|
115
|
May 7, 2026
|
|
This is NEW - I think -
|
|
3
|
109
|
May 7, 2026
|
|
Endmill plunging full depth when pocket cutting
|
|
2
|
75
|
May 5, 2026
|
|
Probe for Center Bore with Nymolab NBS-6040
|
|
2
|
49
|
May 5, 2026
|
|
Tool change wrong tool shown
|
|
2
|
53
|
May 3, 2026
|
|
gSender adjustments
|
|
22
|
282
|
May 2, 2026
|
|
Outline Function
|
|
2
|
78
|
April 30, 2026
|
|
V1.6.0 - Spindle On Delay Not Working
|
|
4
|
83
|
April 30, 2026
|
|
gSender 1.6 - enable blanking
|
|
6
|
104
|
April 30, 2026
|
|
Macro calculating tool length difference
|
|
4
|
90
|
April 30, 2026
|
|
Z axis shoots up. Then doesn't go down during carve
|
|
2
|
61
|
April 29, 2026
|
|
Display A Axis Controls
|
|
7
|
82
|
April 28, 2026
|
|
Run away jog issue
|
|
9
|
135
|
April 28, 2026
|
|
GSender is free but, why?
|
|
7
|
196
|
April 27, 2026
|
|
Gsender 1.6 update question
|
|
18
|
241
|
April 26, 2026
|