|
Goto Z=0 moves far down below zero
|
|
16
|
116
|
September 8, 2026
|
|
TLS stuck after post processor update
|
|
5
|
90
|
September 4, 2026
|
|
GSender always showing Probe input on when it isn't
|
|
2
|
64
|
August 21, 2026
|
|
Autozero touch plate flying
|
|
12
|
147
|
August 15, 2026
|
|
Fixed location tool change issue soft limits
|
|
72
|
1225
|
August 14, 2026
|
|
Pause button should switch to resume!
|
|
1
|
61
|
August 6, 2026
|
|
"Move to" issue
|
|
5
|
72
|
July 16, 2026
|
|
Error on Resume Line # 815908
|
|
5
|
120
|
July 4, 2026
|
|
Router not turning on automatically
|
|
2
|
68
|
July 3, 2026
|
|
Repeatable squaring bug
|
|
7
|
159
|
June 29, 2026
|
|
Laser offset not working
|
|
3
|
104
|
June 26, 2026
|
|
G sender sticking worse with latest software update
|
|
2
|
133
|
June 17, 2026
|
|
Connecting with Wireless Control Halts Job
|
|
0
|
48
|
June 16, 2026
|
|
Possible issue with gSender and grblHAL
|
|
8
|
162
|
June 15, 2026
|
|
While running code gSender goes into 'Hold' and can't recover
|
|
5
|
88
|
June 12, 2026
|
|
Possible gSender issue after stopping, rehoming and re-starting job on GRBL 1.1h
|
|
0
|
70
|
June 8, 2026
|
|
Tool change wizard
|
|
0
|
61
|
June 7, 2026
|
|
Park keyboard shortcut not working
|
|
2
|
69
|
June 1, 2026
|
|
MSG comments not displayed in M0 pause dialog when using Code strategy [Edge-4]
|
|
2
|
65
|
May 28, 2026
|
|
ATC setting not holding RE TLS probing
|
|
2
|
112
|
May 27, 2026
|
|
Front left corner button, no Z raise before XY movement
|
|
2
|
57
|
May 25, 2026
|
|
When leaving rotary mode gsender not going to back the default
|
|
2
|
87
|
May 19, 2026
|
|
XY zero set at edge of bit not center
|
|
0
|
68
|
May 15, 2026
|
|
Fixed Tool Sensor "Probe Changed Tool" button permanently greyed out [Edge-4, grbl, macOS]
|
|
7
|
101
|
May 14, 2026
|
|
Tool change wrong tool shown
|
|
2
|
66
|
May 3, 2026
|
|
V1.6.0 - Spindle On Delay Not Working
|
|
4
|
112
|
April 30, 2026
|
|
Run away jog issue
|
|
9
|
167
|
April 28, 2026
|
|
Park Not Working In 1.6.0
|
|
1
|
61
|
April 23, 2026
|
|
Auto probe fail after firmware update
|
|
1
|
74
|
April 23, 2026
|
|
Possible memory leak?
|
|
7
|
142
|
April 22, 2026
|