|
About the ❓ Something's Up category
|
|
1
|
449
|
December 2, 2024
|
|
Z Axis Issue: Cannot Error Code when job is started in GSender (tall work piece)
|
|
1
|
16
|
October 31, 2026
|
|
Altmill x axis gap
|
|
4
|
132
|
October 29, 2026
|
|
Machine getting really noisy after 10-15 hours of use
|
|
0
|
41
|
October 29, 2026
|
|
MK3 with Autospin Router hitting Y2 axis
|
|
5
|
41
|
October 28, 2026
|
|
Air consumption with ATC?
|
|
3
|
56
|
October 28, 2026
|
|
Binding on Z-Axis after Installing new anti-backlash nuts
|
|
2
|
45
|
October 25, 2026
|
|
Hello. Newbie here. Machine setup Problems
|
|
3
|
79
|
October 21, 2026
|
|
Hard limit alarm when spindle starts
|
|
2
|
80
|
October 20, 2026
|
|
Questions About 2Nm Closed-Loop Motor and SLB-EXT Controller
|
|
2
|
58
|
October 19, 2026
|
|
Problems with jogging
|
|
7
|
117
|
October 19, 2026
|
|
Z Probe Not Wanting To
|
|
4
|
105
|
October 15, 2026
|
|
Issues over RS485 with PWN CNC spindle?
|
|
4
|
93
|
October 14, 2026
|
|
Altmill Disconnected and Won't Reconnect
|
|
4
|
63
|
October 13, 2026
|
|
LongMill MK2 Y1 displacement different from Y2
|
|
8
|
68
|
October 13, 2026
|
|
Turn off Z jumps
|
|
12
|
118
|
October 7, 2026
|
|
Schematic for Lonmill MK1 1.4.2
|
|
2
|
53
|
October 5, 2026
|
|
Plasma torch control
|
|
2
|
74
|
September 30, 2026
|
|
Altmill isn't Altmilling
|
|
9
|
148
|
September 27, 2026
|
|
Autospin Drama & Fix - In case someone has the same issue
|
|
0
|
68
|
September 24, 2026
|
|
Super Long Board, Y axis issue
|
|
2
|
54
|
September 18, 2026
|
|
Altmill tramming issues with eccentric travel
|
|
6
|
117
|
September 17, 2026
|
|
Problem with Tool Length Sensor
|
|
6
|
208
|
September 15, 2026
|
|
No access to the console
|
|
4
|
83
|
September 12, 2026
|
|
Spindle delay is not delaying!
|
|
1
|
73
|
September 10, 2026
|
|
Machine Stops moving - GSender keeps going
|
|
4
|
88
|
September 2, 2026
|
|
X axis clicking noise
|
|
1
|
75
|
September 2, 2026
|
|
No connectivity after failed firmware upgrade
|
|
18
|
242
|
September 1, 2026
|
|
Auto zero touch plat help
|
|
3
|
80
|
August 29, 2026
|
|
Solved: Alarm 10 / E-stop not working on SLB-EXT - and yes, it was my fault!
|
|
1
|
72
|
August 26, 2026
|