|
About the Machine Support category
|
|
1
|
576
|
December 23, 2021
|
|
X Axis will not hold the Zero out and stalls when running the quick check from IDC WoodCraft spoil board gcode
|
|
1
|
38
|
November 28, 2022
|
|
Not sure what’s going on
|
|
0
|
43
|
November 27, 2022
|
|
Emergency stop button
|
|
0
|
39
|
November 26, 2022
|
|
GRBL randomly disconnecting during carve
|
|
7
|
130
|
November 25, 2022
|
|
Do I have the correct Y-axis gantry for the 48x30
|
|
6
|
65
|
November 22, 2022
|
|
Router Crash = EMI ? ! ⚡
|
|
3
|
79
|
November 17, 2022
|
|
Break in and Building then Surfacing the Spoil board and gcode help
|
|
2
|
81
|
November 16, 2022
|
|
Auto touch plate alarm
|
|
13
|
126
|
November 12, 2022
|
|
Need help with New laptop as my old one will not connect to to my new 48 x 30 Longmill MK2
|
|
10
|
109
|
November 10, 2022
|
|
Thoughts on connection issues. posible board?
|
|
1
|
67
|
November 9, 2022
|
|
Zaxis problems with rerunning job
|
|
8
|
178
|
November 7, 2022
|
|
Project runs fine once, but not a second time
|
|
1
|
50
|
November 7, 2022
|
|
Laser setting for 3mm
|
|
0
|
35
|
November 7, 2022
|
|
MK2 Humming while connected to gSender
|
|
4
|
67
|
November 6, 2022
|
|
LongMill 30x30 vs 48x30
|
|
2
|
51
|
November 6, 2022
|
|
Slippy X- how about 2 antibacklash nuts on it?
|
|
4
|
71
|
November 3, 2022
|
|
Homing sensor Y not triggering alarm
|
|
0
|
45
|
November 1, 2022
|
|
Y-Axis Motor Randomly Turning In Wrong Direction
|
|
4
|
64
|
November 1, 2022
|
|
Bit size for my engraving with a longmill machine
|
|
5
|
54
|
October 29, 2022
|
|
1/4" bit keeps getting deeper and deeper
|
|
1
|
65
|
October 27, 2022
|
|
Never been able to properly tension right side Y
|
|
5
|
110
|
October 26, 2022
|
|
X and y axis problems
|
|
5
|
68
|
October 26, 2022
|
|
Y axis out...help please?
|
|
5
|
92
|
October 25, 2022
|
|
XYZ axis not stable
|
|
1
|
83
|
October 25, 2022
|
|
X axis step cut
|
|
5
|
117
|
October 25, 2022
|
|
Jogging lock issue
|
|
0
|
48
|
October 19, 2022
|
|
Where to ask pre-purchase questions?
|
|
2
|
57
|
October 19, 2022
|
|
Touch Plate homing activation
|
|
2
|
63
|
October 18, 2022
|
|
X motor coupling not locking on shaft
|
|
4
|
64
|
October 18, 2022
|