|
New Altmill 4X4 tested 2" square on Vcarve CNC making 1 foot sq?
|
|
4
|
117
|
June 25, 2026
|
|
List of gcode commands
|
|
2
|
143
|
June 25, 2026
|
|
GSender issues connecting to SLB
|
|
14
|
271
|
June 21, 2026
|
|
Issues with ATC settings after grblHAL update
|
|
6
|
155
|
June 18, 2026
|
|
G sender sticking worse with latest software update
|
|
2
|
143
|
June 17, 2026
|
|
Can't copy to clipboard or notepad from GSender
|
|
13
|
177
|
June 16, 2026
|
|
Firmware Upgrade and PWNCNC Spindle
|
|
2
|
94
|
June 16, 2026
|
|
Connecting with Wireless Control Halts Job
|
|
0
|
51
|
June 16, 2026
|
|
Possible issue with gSender and grblHAL
|
|
8
|
168
|
June 15, 2026
|
|
While running code gSender goes into 'Hold' and can't recover
|
|
5
|
92
|
June 12, 2026
|
|
Laser offset not showing in config of 1.61
|
|
3
|
62
|
June 12, 2026
|
|
Suggestion: clarify SLB firmware vs GRBL version in Machine Information / docs
|
|
5
|
137
|
June 9, 2026
|
|
Possible gSender issue after stopping, rehoming and re-starting job on GRBL 1.1h
|
|
0
|
74
|
June 8, 2026
|
|
Tool change wizard
|
|
0
|
64
|
June 7, 2026
|
|
Vector-Based Auto-Leveling & Dynamic XY/Z Zeroing for Organic Shapes
|
|
10
|
139
|
June 3, 2026
|
|
My CNC was working, but now not
|
|
2
|
101
|
June 3, 2026
|
|
Feature Request: Unlock Manual Tool Table / Nicknames for non-SLB users (FluidNC/RatRig)
|
|
19
|
312
|
June 1, 2026
|
|
MSG comments not displayed in M0 pause dialog when using Code strategy [Edge-4]
|
|
2
|
65
|
May 28, 2026
|
|
Gsender slow to move router
|
|
2
|
78
|
May 28, 2026
|
|
ATC setting not holding RE TLS probing
|
|
2
|
115
|
May 27, 2026
|
|
Auto probe not in initial expected state
|
|
3
|
86
|
May 26, 2026
|
|
Front left corner button, no Z raise before XY movement
|
|
2
|
60
|
May 25, 2026
|
|
Cannot adjust feedrate during surfacing
|
|
3
|
95
|
May 24, 2026
|
|
Problems running macros from the SD card
|
|
7
|
169
|
May 21, 2026
|
|
When leaving rotary mode gsender not going to back the default
|
|
2
|
91
|
May 19, 2026
|
|
Heightmap gSender
|
|
65
|
2821
|
May 19, 2026
|
|
Gsender w/Genmitsu Wireless Controller
|
|
4
|
143
|
May 18, 2026
|
|
XY zero set at edge of bit not center
|
|
0
|
69
|
May 15, 2026
|
|
Spindle Speed Display
|
|
4
|
148
|
May 14, 2026
|
|
Fixed Tool Sensor "Probe Changed Tool" button permanently greyed out [Edge-4, grbl, macOS]
|
|
7
|
114
|
May 14, 2026
|