|
MSG comments not displayed in M0 pause dialog when using Code strategy [Edge-4]
|
|
2
|
68
|
May 28, 2026
|
|
Gsender slow to move router
|
|
2
|
83
|
May 28, 2026
|
|
ATC setting not holding RE TLS probing
|
|
2
|
117
|
May 27, 2026
|
|
Auto probe not in initial expected state
|
|
3
|
88
|
May 26, 2026
|
|
Front left corner button, no Z raise before XY movement
|
|
2
|
61
|
May 25, 2026
|
|
Cannot adjust feedrate during surfacing
|
|
3
|
95
|
May 24, 2026
|
|
Problems running macros from the SD card
|
|
7
|
177
|
May 21, 2026
|
|
When leaving rotary mode gsender not going to back the default
|
|
2
|
91
|
May 19, 2026
|
|
Heightmap gSender
|
|
65
|
2867
|
May 19, 2026
|
|
Gsender w/Genmitsu Wireless Controller
|
|
4
|
153
|
May 18, 2026
|
|
XY zero set at edge of bit not center
|
|
0
|
71
|
May 15, 2026
|
|
Spindle Speed Display
|
|
4
|
154
|
May 14, 2026
|
|
Fixed Tool Sensor "Probe Changed Tool" button permanently greyed out [Edge-4, grbl, macOS]
|
|
7
|
126
|
May 14, 2026
|
|
Visualizer no longer working in gSender 1.6?
|
|
0
|
57
|
May 13, 2026
|
|
Automations line pause
|
|
24
|
294
|
May 13, 2026
|
|
AutoZero incorrect Z height
|
|
6
|
152
|
May 13, 2026
|
|
Please Restore "Prompt for first tool" option in Edge-4 Tool Changing settings
|
|
1
|
57
|
May 13, 2026
|
|
Z Drive goes to the top limit upon starting a cut
|
|
5
|
107
|
May 13, 2026
|
|
Wear diameter compensation
|
|
6
|
162
|
May 7, 2026
|
|
This is NEW - I think -
|
|
3
|
134
|
May 7, 2026
|
|
Endmill plunging full depth when pocket cutting
|
|
2
|
96
|
May 5, 2026
|
|
Probe for Center Bore with Nymolab NBS-6040
|
|
2
|
103
|
May 5, 2026
|
|
Tool change wrong tool shown
|
|
2
|
72
|
May 3, 2026
|
|
gSender adjustments
|
|
22
|
391
|
May 2, 2026
|
|
Outline Function
|
|
2
|
85
|
April 30, 2026
|
|
V1.6.0 - Spindle On Delay Not Working
|
|
4
|
119
|
April 30, 2026
|
|
gSender 1.6 - enable blanking
|
|
6
|
116
|
April 30, 2026
|
|
Macro calculating tool length difference
|
|
4
|
124
|
April 30, 2026
|
|
Z axis shoots up. Then doesn't go down during carve
|
|
2
|
107
|
April 29, 2026
|
|
Display A Axis Controls
|
|
7
|
102
|
April 28, 2026
|